All posts by matchbow92

This Is A Guide To Kia Picanto Key Fob Replacement In 2023
How to Replace a Kia Sportage Replacement Key 
 
The key on many Kia models has a keyless entry system built in. The key functions like the remote control, and can be exchanged by an Kia dealer. 
 
Key fobs may stop working due to a variety of reasons, such as batteries that are dead, worn-out buttons signal interference or water damage. Here are some tips on how to get your Kia Sportage replacement key back to working. 
 
How to replace the remote key or smartkey 
 
The battery in your Kia's intelligent key will eventually have to be replaced, regardless of whether it is a remote key, a push-to-start key or a normal metal key that doesn't contain an electronic transponder. This is particularly true if your car displays a message indicating that the smart or remote keys are not powered by batteries. 
 
It's a fairly simple process. To replace the keyfob battery take out your mechanical key from the slit that is located at the back of the fob. Then, pry the cover open. Inside the key fob, there will be a small screw that holds the battery in its place. By using a small screwdriver take the screw off and pull out the old battery. Install the new battery and then close the cut on the key fob. 
 
Test the key fob by pressing the lock/unlock buttons. You're good to go If the doors lock and unlock as you expect. You can now make use of the hands-free lock/unlock feature on your Kia whenever your fingers get chilly or you need to do some errands in Brandon. 
 
Note: Some key fobs (transponder chip or smart keys) might require their programming done. This requires a machine for programming that is available only to the automotive locksmith or dealer. Other keys (non-transponder metal keys) don't require programming. If you're required to reprogramme your key, you'll have to note the key code's number on the tag for the key code. 
 
How do you replace the battery? 
 
If the Kia key fob is unable to respond when you press the lock/unlock button, it is likely that the battery is insufficient. A low battery could cause other issues, such as the check engine light coming on or the engine not cranking. Fortunately, replacing the key fob battery is a simple DIY project that requires only the most basic tools. 
 
Before you begin ensure that your vehicle is turned off and that all doors are closed. Find the small, metal or plastic piece that is located at the bottom of the key fob. Move it until the key comes out. Then, you can insert this key into the door handle of the driver to unlock your car. 
 
To replace the battery inside the key fob remove the rear cover. Utilize a plastic plier tool to loosen up the latch that holds the black negative cable. Remove the old battery, and then align the replacement battery to ensure that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid bending or damaging the contacts made of metal. 
 
 
After installing the new battery, turn the key fob on and off in the ignition until the door locks cycle. You can then test your Kia's key fob once more to ensure it's working properly. 
 
How do I replace a smart key 
 
Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The difference between these is that the smart key comes with an incredibly small key blade tucked inside it, while the standard key fob does not. Both key fobs contain an internal battery that will eventually require replacement. It is a simple process that takes less than two minutes. 
 
Before you begin it is essential to make sure that you are on a flat surface with adequate lighting and that your Kia is turned off. Be aware that the fob has tiny pieces that could fall should you not be careful. 
 
The first step is to locate the small release button on the lower backside of the fob. It will be a circular button or rectangular slot. You can open the key fob by pressing the button. 
 
Once you have the key fob open and you are able to remove the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. When you're done, the key fob should permit you to lock and unlock your vehicle, even if it isn't running. 
 
How do you replace a broken mechanical key 
 
The Kia key fob is an amazing convenience that lets us lock and unlock our car with the push of a button. But, as with all devices it may have issues from time to time. There are ways to resolve these issues and keep your key fobs functioning for the duration of. 
 
A dead or weak battery is one of the most common issues. This could cause the fob to stop working completely or stop working at times. If this happens then try replacing the battery with a new one. 
 
If this isn't enough to solve the issue, try using an ordinary screwdriver with a flat head to push the fob's plastic casing open. Be cautious not to damage any internal components or scratch the plastic. After G28CarKeys has been removed and replaced, you can replace it with a brand new one. 
 
When the new battery is in, close and open the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that can fit into the slot). Test the key fob to ensure it's functioning properly. Contact a dealer, or a locksmith to address the issue in the event that the fob is not working. Make sure they make you an emergency key that can work for all trunk and door cylinders in order to avoid lockouts in the future.